Secure Fit for the Milwaukee Ratcheting Wrench SAE/METRIC Set
These premium quality inserts are custom made for the Milwaukee Ratcheting Wrench set (part number 48-22-9416) set in both SAE and METRIC for the 3-drawer PACKOUT box are a great addition to any automotive tools enthusiasts.
- Fits: PACKOUT 48-22-8443 (3 drawer), 48-22-8442 (2 drawer), 48-22-8447 (3 drawer multi-drawer, only in the bottom drawer). Will not fit the 4-Drawer box.
- Tool: Milwaukee Ratcheting Wrenches (48-22-9416)
- Holds: Metric and SAE Ratcheting Wrenches
- Material: PLA+
- Colors: Black with Red lettering and Red with Black lettering
Where to buy?
Currently our products are hosted on either eBay or Etsy, so you can securely buy them with your preference of which one suits your needs best.
If you need help with common questions, help installing, or troubleshoot common issues such as fitment here are some helpful resources below:
Will this fit my PACKOUT Drawer?
Fitment with PACKOUT Drawer boxes: Will fit the 2 drawer as well as the larger drawer from the 3 drawer (2 small drawers and 1 large drawer box). Will not fit in the small drawers of the PACKOUT boxes like the 4 drawer. Will only fit in the medium sized and large sized drawers. These part numbers are what these inserts are compatible with: 48-22-8443 (3 drawer), 48-22-8442 (2 drawer), 48-22-8447 (3 drawer multi-drawer, only in the bottom drawer). Will not fit the 4 drawer (48-22-8444).
Is the insert removable?
Yes, you can lift the insert out when needed. It is not permanently mounted.
What material is it made from?
The inserts are 3D printed using durable PLA+ and should hold up fine under normal use and conditions. Prolonged direct sunlight for many days at a time is not recommended as that can degrade the plastic over time. But normal use should not be a problem! Basically, don’t leave them outside in the sun unattended for an extended time (days).
How do I clean it?
Wipe with a damp cloth. Do not soak or use harsh chemicals, as they may degrade the print finish.
Before You Start:
- Make sure you have the 3-drawer, 2-drawer, or larger of the 3-drawer multi drawer packout boxes.
- Unload any items from the organizer and wipe it clean of dust or debris.
1. Place the Inserts
Gently slide each insert into the drawer, put the bottom insert in first then the top one. Repeat on the other side so 2 black are on the right and 2 red are on the left.
2. Load Your Wrenches
Start loading your wrenches into the appropriate slots. They can go in either up or down facing direction. The 1″ wrench (largest) goes at the very top.
3. Close Drawer and Test Fit
- Close the Packout lid gently and verify everything clears the Drawer.
4. Optional AirTag Holder
Newer model inserts have a small cutout on the bottom of the top of the red SAE insert to allow for an Apple AirTag or similar sized Android tag to be placed in the slot.
It’s advised to also put a piece of tape over the bottom slot once the AirTag is installed as that will prevent it from falling out.
If you do not wish to use an AirTag or similar Android tag, then either leave the slot empty.
Inserts fit too tightly, hard to install them into the PACKOUT box?
These are precision fit inserts so they can be a bit tight installing at first. What you want to do is place the bottom insert in first, and hold it firmly against the bottom of the box as you gently lay down the top insert. Place even pressure to ensure the inserts (top and bottom) lay flat against the bottom of the box and they should snap in. Check the Help Page for more solutions.
The inserts were left in the sun or extreme heat and they look like they have warped a bit
Sun exposure is something these inserts are warned about when your item was shipped to you, with a giant sticker that warned to keep out of the sun or extreme heat. These inserts are printed in a way to help mitigate this from happening, but there are several ways it can warp, not all are bad or impedes functionality. For example, it may warp slightly on the bottom of the inserts, where there is a bit of a hollow gap in the way it prints, so if the bottom looks bubbly in a way, that’s not something that can impede functionality as its on the bottom and out of sight. However if a wall of the print looks warped and that is something visible and is causing the functionality to be impaired, that is another matter. For these issues, its best to email pictures of the warping to info@handy3dprint.com and see if there are any warranty options available. Typically the warranty policy is as long as you the buyer are OK with paying for shipping, then sending a replacement part is something that we can do. We are not a big store like amazon to afford free shipping so if you can cover the shipping label (under $10) then in most cases sending a replacement part isn’t a big deal.